Rebuildable Atomizer

PATRIOT
The Patriot Atomizer by Innovape Mods has been designed, engineered and manufactured in the United States.
Its high volume tank equals higher air flow for larger vapor clouds; more room for wick equals more juice for more hits. Measures 22mm for a flush look on most mods.
The Patriot Atomizer is made with precision machined components from the highest grade 303 stainless steel ensure exact fits for consistent, even current draw to coils.
Available in stainless steel or gold plated .

Precisely sized vapor ports allow laminar flow for a clean steady pull
with no turbulence in the vape stream
Zero resistance press fit terminal posts keep the power constant on every hit.
Unique dynamic quad ring seal keeps any extra juice inside the tank
Through hole terminal design guarantees positive multi-point electrical contact to deliver maximum current to the coils.
Dual o-ring design adds mechanical stability to tank and drip tip while keeping the air stream on the coils where you want it to maximize the vape.
Unique heat sink fin gives it that custom look and design and also removes up to 50% more heat during a chain vape.
Patriot Parameters
Type: Rebuildable dripping atomizer
Length: 49mm
Diameter: 20mm
Weight: 49g
Resistance: 1.8-2.8omh
Material: Stainless steel
Color: Stainless steel
Thread: 510

•NIMBUS•

NIMBUS V5 clone Features The "Spit Back Protection" does the following: as the name suggests, it protects you from the irritating spitbacks you get when your dripper gets "flooded" by your ejuice. it also serves as a "Flavor Booster" because of the hole size inside the driptip hole. It concentrates the vapor from the wick to your taste buds or mouth so that you taste your juice better.
NIMBUS is the ONLY Filipino Made Atomizer that has a Spit Back protection
The NIMBUS Atomizer has TWO insulators (another first here in the Philippines). The one on top is a soft insulator, this one serves as a warning about how you treat your NIMBUS, if it gets bloated you're it means you're torching your NIMBUS directly straight into the insulator(i know it sounds stupid, but a lot of people to this.) The other insulator on the bottom part is made of PA66 it's high heat resistance and placement makes it near impossible to destroy (not unless you're really trying to destroy it).
The Juice Well is a nice thing to add specially for some "Over Droppers" out there. With this, the excess juice that falls from your wick will stay below it and when it's time to the wick will absorb the excess juice too...so NO WASTED JUICE from your atty now
The Three Poles of the NIMBUS RA makes Dual Coil or even QUAD Coil builds easier to make. Oh and the holes in the poles makes rebuilding your wicks easier too!

•OMEGA•
The Omega atomizer clone is a rebuildable dripping atomizer. The Omega RDA clone is a high quality drip atomizer that is made out of stainless steel. This is a stainless steel dripping atomizer that has three posts, which can support various dual coil, or single coil builds. The top-cap comes off and the Omega clone has 3 big airflow holes pre-drilled which are adjustable by rotating the top cap. The Omega RDA clone has a standard 510 connector.

•HELIOS•

Introducing the Helios Rebuildable Dripping Atomizer

The Helios by VHO outshines the competition, allowing for effortless multi-coil builds via its unique center T-post design and spinning cap for the ultimate in airflow control. One of the only RDAs out there specifically designed to accommodate a QUAD coil setup!

Seamless 304 Stainless Steel, Tri-Pole with 4 connection points. Air-Flow Control ring with 2 and they are 1.5mm each. High-Temperature Insulator and Feasible for single, dual, quad to octa build.

Features :
- 304 SS grade material
- Adjustable Quad post design
- Adjustable spinning cap designed for airflow control
- Built in AFC
- High temp insulator
- Juice well

(Hit the drop down box to select your dripper of choice)